 |
|
|
|
|
|
|
 |
 |
 |
|
|||
 |
|
|||||
2021 Arch St., Philadelphia, PA 19103
Phone: 856.491.5901 |
|
|||||
 |
|
|||||
 |
 |
 |
 |
|
||
 |
 |
|||||
Material Data Sheets - Chart 3
|
Property |
Units | Test Method ASTM |
Nylon 101 |
Poly- carbonate |
UHMWPE | Polyether- sulfone |
| Specific Gravity | -- | D-792 | 1.14 - 1.15 | 1.20 | 0.94 | 1.37 |
| Tensile Strength, 73°F | psi | D-638 | 9,000 - 12,000 | 9,000 - 10,500 | 4,000
- 5,000 |
12,280 |
| Tensile
Modulus of Elasticity, 73°F |
psi | D-638 | 250,000 - 400,000 | 320,000 | 80,000 - 100,000 | 390,000 |
| Elongation, 73°F | % | D-638 | 20-280 | 50-100 | 280-450 | 40-80 |
| Flexoral Strength, 73°F | psi | D-790 | 12,500 - 14,000 | 11,500 - 12,500 | -- | 18,700 |
| Flexoral
Modulus of Elasticity, 73°F |
psi | D-790 | 175,000 - 410,000 | 310,000 - 500,000 | 75,000 | 373,000 |
| Shear Strength, 73°F | psi | D-732 | 9,600 | -- | 3,500 | -- |
| Compressive Strength | psi | D-695 | 5,000 | 10,000 - 14,000 | -- | -- |
| Compressive
Modulus of Elasticity, 73°F |
psi | D-695 | -- | -- | -- | -- |
| Coefficient of Friction (Dry vs. Steel) Dynamic | -- | -- | .17 - .43 | -- | .09 - .12 | -- |
| Hardness, Rockwell, 73°F | -- | D-785 | R110-120 | R110-120 | R64 | 88 |
| Hardness, Durometer, 73°F | -- | D-676 | D80-85 | D80-85 | -- | -- |
| Tensile Impact, 73°F | ft.lb. / in(2) | D-1822 | 90-280 | -- | 1,000 | -- |
| Property | Units | Test Method ASTM |
Nylon 101 |
Poly- carbonate |
UHMWPE | Polyether- sulfone |
| Coefficient of Linear Thermal Expansion | in./in./°F | D-696 | 5.5 x 10(-5) | 3.9 x 10(-5) | 7.2 x 10(-5) | 5.5 x 10(-5) |
| Deformation
under Load (122°F, 2,000 psi) |
% | D-621 | 1.0 - 3.0 | 0.2(-3) 280-290 | 6-8 (6 hrs.) |
-- |
| Deflection
Temperature, 264 psi |
°F | D-648 | 280-450 | 283-293 | 158-174 | 398 |
66 psi |
°F | D-648 | 400-460 | 514 +/- 9 | 266 | -- |
| Melting Point | °F | D-789 | 482-500 | -- | -- | -- |
| Continuous
Service Temperature in Air (max) |
°F | -- | 280-280 | 250 | 160/280 | 398 |
| Dielectric
Strength, Short Time |
volts / mil. | D-149 | 300-400(2) | 400(2) | 450-500(2) | 400 |
| Volume Resistivity | ohm-cm. | D-257 | 4.5 x 10(13) | 2.1 x 10(16) | 10(18) | 3.1 x 10(-5) |
| Dielectric Constant, 60 Hz | -- | D-150 | 4.1 | 3.17 | 2.3 | 3.5 |
10(3) Hz |
-- | D-150 | 4.0 | 3.1 | -- | -- |
10(6) Hz |
-- | D-150 | 3.4 | 2.96 | -- | -- |
| Property | Units | Test Method ASTM |
Nylon 101 |
Poly- carbonate |
UHMWPE | Polyether- sulfone |
| Water
Absorption, Immersion (24 hours) |
% | D-570 | 0.6-1.5 | 0.2 | < .01 | |
| Water Absoption, Saturation | % | D-570 | 7-9 | -- | -- | -- |
| Acids, Weak, 73°F | -- | -- | A | A | A | A |
| Acids, Strong, 73°F | -- | -- | U | U | L | A |
| Alkalies, Weak, 73°F | -- | -- | A | L | A | A |
| Strong, 73°F | -- | -- | A | U | A | A |
| Hydrocarbons, Aromatic, 73°F | -- | -- | A | U | L | -- |
| Hydrocarbons, Aliphatic, 73°F | -- | -- | A | U | A | -- |
| Ketones, 73°F | -- | -- | A | U | A | -- |
| Ethers, 73°F | -- | -- | A | U | A | -- |
| Esters, 73°F | -- | -- | A | U | A | -- |
| Alcohols, 73°F | -- | -- | A | U | A | -- |
| Inorganic Salt Solutions, 73°F | -- | -- | A | -- | A | -- |
| Continuous Sunlight, 73°F | -- | -- | L | L | U | -- |
KEY
| A | = Acceptable Service | (1) | ASTM B-1457 used for thin specimens |
| L | = Limited Service | (2) | .080" thick |
| U | (3) | 122 F, 4,000 psi | |
| NR | = Not Rated | (4) | ASTM
D-1708 (1/8" thick specimen @ .05"/min.) |
| -- | = Must Check Concentration | (5) | 00 psi |
| (6) | .040" thick | ||
| (7) | Specimen
1/8" thick, 2" diameter |
|
|
|
|
|
|
|
|
|
|
 |
 |
 |
 |
|
|||||
 |
 |
 |
|
|
|||||
 |
 |
|
|||||||